DIN 58545-1996 标准绘图仪铅笔芯或分度器
作者:标准资料网 时间:2024-05-14 18:35:43 浏览:9713
来源:标准资料网
【英文标准名称】:Pencilpointsordividerpointsforstandarddrawinginstruments(S)
【原文标准名称】:标准绘图仪铅笔芯或分度器
【标准号】:DIN58545-1996
【标准状态】:现行
【国别】:德国
【发布日期】:1996-11
【实施或试行日期】:
【发布单位】:德国标准化学会(DIN)
【起草单位】:
【标准类型】:()
【标准水平】:()
【中文主题词】:针;材料;名称与符号;尺寸;绘图室设备;制图仪器;铅笔插头;笔芯
【英文主题词】:materials;dimensions;needles;pencilpoints;designations;penrefills;drawinginstruments;drawingofficeequipment
【摘要】:Thedocumentcontainsrequirementsanddimensionsforpencilpointsordividerpointsforstandarddrawinginstruments.
【中国标准分类号】:Y50
【国际标准分类号】:01_100_40
【页数】:2P;A4
【正文语种】:德语
【英文标准名称】:GuideforQualityControlCharts,MethodofAnalyzingData,andControllingQualityduringProduction/Note:reaffirmationofANSI/ASQCB1,B2,B3-1985*Approved1996-03-08.
【原文标准名称】:质量控制图表、数据分析方法和生产中质量控制用指南.注:ANSI/ASQCB1,B2,B3-1985的重申.1996-03-08批准
【标准号】:ANSI/ASQCB2-1985
【标准状态】:现行
【国别】:美国
【发布日期】:1985
【实施或试行日期】:
【发布单位】:美国国家标准学会(US-ANSI)
【起草单位】:
【标准类型】:()
【标准水平】:()
【中文主题词】:
【英文主题词】:
【摘要】:Outlinesthecontrolchartmethodofidentifyingandeliminatingcausesoftroubleinrepetitiveproductionprocessesinordertoreducevariationinthequalityofmanufacturedproductsandmaterials.
【中国标准分类号】:A00
【国际标准分类号】:03_120_10
【页数】:
【正文语种】:英语
Product Code:SAE USCAR35
Title:Test Procedures for Evaluating Bolt-Load Retention of Magnesium Alloy
Issuing Committee:
Scope:1.1 A bolt-load retention (BLR) test is a practical test to determine the bolt load of a fastener joint with time and at given temperatures. There are three types of BLR tests described in this standard, namely general-purpose test, design-purpose test, and screening material test. A general-purpose BLR test may be used for screening materials, while a design-purpose BLR test is usually used to verify the BLR behavior of a specific joint. The screening material test is an example of the general-purpose test for typical automotive applications.1.2 The test procedures provides guidance in the following areas: (a) BLR sample and test fixture, (b) test fastener, washer and nut, (c) bolt-load measurement and data acquisition, (d) heating device, (e) initial loading, (f) baseline test, and (g) instrumentation of strain gages and calibration (see Appendix B). A design-purpose test procedure differs from a general-purpose test procedure mainly in the areas dealing with sample and fixture, test washer and nut, and initial loading. 1.3 This standard is intended to evaluate and/or validate BLR of magnesium alloys, especially cast magnesium alloys, for automotive applications. It is implied that the test samples mentioned in this standard are to be produced from casting processes but are not restricted to castings and magnesium alloys.This standard is intended to evaluate BLR behavior during long-duration BLR tests. The effect of thermal cycling without holding the samples at high temperatures for a long period of time is discussed in Appendix C.
